Stationeers

Stationeers

(Outdated) Print-Success
14 Comments
kn-heal 20 Feb, 2023 @ 9:20pm 
plz update
никита 6 Apr, 2021 @ 8:31pm 
Thank you for your advice ! I will try.
Manny K SoSo  [author] 3 Apr, 2021 @ 11:45am 
@pit1.9.8.1 this is likely because the code is written in English so things like Copper in the code need to be replaced with your native language variant. I've talked to the dev's about this issue and they are unsure if this is intended or a bug. But you can either change the code variables from "Copper" to your native language or switch to using English.
никита 3 Apr, 2021 @ 10:50am 
код вообще отказался работать и на корпусе ic10 показывает состояние ноль . при переключения количества печати даже показания на дисплее не меняются и ошибок не каких не показывает
Manny K SoSo  [author] 2 Apr, 2021 @ 6:04pm 
@pit1.9.8.1 The script reads the printer all lets you know if you can print them, it does not stop you from printing them. Its more for letting you know if what you are going to print will actually work.
никита 2 Apr, 2021 @ 8:48am 
good afternoon! I tried with the electronics printer, it does not work quite successful printing, even the hash display does not show anything, there are no errors on the case and the state is 0, ic10 on the printer itself works perfectly .
Manny K SoSo  [author] 14 Feb, 2021 @ 8:51am 
For those who where following this the issue was that the localization caused variables calls like loading Copper to use the language of whatever is set for Stationeers.
Ellmite 5 Feb, 2021 @ 5:04am 
send you an invite
Manny K SoSo  [author] 4 Feb, 2021 @ 12:26pm 
@Ellmite Can you upload your world so I can take a look at it. I just opened my test world and loaded the code with the electronic printer and it cycled just fine.
Manny K SoSo  [author] 4 Feb, 2021 @ 10:32am 
Hmmmm, I will have to do some digging into this one. I will test with the electronic printer and see if its an issue with it (the dev's may have changed the way it works). I will get back to you if I find the issue.
Ellmite 3 Feb, 2021 @ 6:28pm 
I use the script for the electronic printer and the print success. I build it 3 times up with your video, but the console with hash display, which is showing the ic print success stands still. In example with the heavy cable, it´s only shows the gold ingot.It switched green, when i put enough gold into the printer but doesn´t show me the copper. when i put the copper into it and start the printing, the displays counts down/up. but the display stands by the gold ingot. when i choose another printing, which has not the gold ingot on the first row in the need-list, it shows me this ingot. but also don`t switch.
Manny K SoSo  [author] 3 Feb, 2021 @ 2:33pm 
I have also double checked everything and I don't see it erroring and its also going through all the ingots fine. It should keep on an ingot for at least 30 ticks (if its the last one in the list it will be there for a bit longer). Double check to make sure you have the connections correct and that the display for the ingots is reading the hash from the IC and that the IC ins't pushing anything to the hash display (since the IC only puts the hash on its setting).
You should also see that the hash is changing if you look at it directly on the IC housing.
Manny K SoSo  [author] 3 Feb, 2021 @ 2:23pm 
@Ellmite Are you using this in conjunction with my autolathe script?
Ellmite 3 Feb, 2021 @ 1:25pm 
I don´t know why, but it works only for products with one ingrident. Products with more ingridents (like heavy cable (gold + copper), it shows only the first ingot of the list and doesn´t rotate between the other.