Hi i liked the furnace so much come back and so much changed is that still actual or is there an update ?

just correctet "bge" r2 and r3 (minpressure) to "ble"

Alright, have written some code, until now i am not exploded and got nearly 6000 Celcius//10MPa for now. i hope it's gonna shut down at 40MPa...
alias PANitro d0
alias PAHydro d1
alias Mixer d2
alias PAOutput d3
alias VPOutput d4
alias HotGasTank d5

define MaxTankPressure 40000
define MaxPipePressure 5000
define MinHydroNitroPressure 1000
main:
yield
l r0 PAOutput Pressure
l r1 HotGasTank Pressure
l r2 PANitro Pressure
l r3 PAHydro Pressure

bge r1 MaxTankPressure NOIgnition
bge r0 MaxPipePressure NOIgnition
bge r2 MinHydroNitroPressure NOIgnition
bge r3 MinHydroNitroPressure NOIgnition

s VPOutput On 1
s VPOutput Setting 100
yield
s Mixer On 1
j main
NOIgnition:
s VPOutput On 0
s Mixer On 0
j main

so no IC10 needed anymore just a mixer? or you mean don't use N20 (i am on Vulcan and i don't have any use for it then heating the furnace for high temperature), i just use normal pipes, should be enough to self ignite... just wanted the safety features that my pipe doesn't explode that's why i was thinkink about using your IC Code

@Holle don't use this, it's not needed anymore. make your own fuel mix and just pressure regulate it into the hot pipe (make sure it's hot first)

Hello Elmo,
what Parameters i have to change, if i want to use N20 instead of Oxygen? I changed the volatiles ratio from 2 to 1 (1:1 Hydrogen and N20), also changed RatioOxygen to RatioNitrousOxide, but nothing happens... just settet up the igniter yet, not the hole furnace. Thank you for advises...

@Magne you don't need to do controlled ignitions anymore, fuel can combust is small partial, meaning you could just hook up fuel mix straight to the hot pump on the furnace, don't need to ignition stuff or the hot buffer.
thus it follows you don't need the ocygentControlelr or hot oxygen anymore either.

Are you thinking of doing a new tutorial? How is the furnace easier now?

@xceled 406 means temperature low. they changed ignition temperature. you can just heat the gasses, but honestly this might be outdated now. furnaces can be done so much easier now.

Could you explain the status codes this can output a bit? I'm getting 406 and not sure why.

@Armand12 OxygenController can manage the hot O2 pressure. but your (cold) O2/H2 source pressure isn't managed in any way on this system. :)

Or I could avoid the spaghetti by just slapping another pipe analyzer down on the heat pipe after the pump like a smart person prolly would.

Ah, see, for some reason I had it in my head that the utility IC managed the hot O2 or H2 buffer BEFORE the ignition chamber, not the pipe AFTER that. I kept looking for how the furnace controller or ignition ICs communicated to regulate that or only generate on command, turns out they don't I suppose. It's an easy enough fix to setup a pressure regulator to maintain a sufficient hot O2 level in my network, buuuut gonna get some spaghetti re-routing that tank to connect to the heat pipe. Such is life.

@Armand12 yes this code doesn't manage that. The Utility IC manages that.

I've setup the complete automated furnace, but the ignition controller seems to run non-stop. It's always generating fresh hot gas to put into the buffer pipe, I have to manually set the exit pipe to 0 to keep it from rupturing my pipe network.