Steam 설치
로그인
|
언어
简体中文(중국어 간체)
繁體中文(중국어 번체)
日本語(일본어)
ไทย(태국어)
Български(불가리아어)
Čeština(체코어)
Dansk(덴마크어)
Deutsch(독일어)
English(영어)
Español - España(스페인어 - 스페인)
Español - Latinoamérica(스페인어 - 중남미)
Ελληνικά(그리스어)
Français(프랑스어)
Italiano(이탈리아어)
Bahasa Indonesia(인도네시아어)
Magyar(헝가리어)
Nederlands(네덜란드어)
Norsk(노르웨이어)
Polski(폴란드어)
Português(포르투갈어 - 포르투갈)
Português - Brasil(포르투갈어 - 브라질)
Română(루마니아어)
Русский(러시아어)
Suomi(핀란드어)
Svenska(스웨덴어)
Türkçe(튀르키예어)
Tiếng Việt(베트남어)
Українська(우크라이나어)
번역 관련 문제 보고
If you can provide references for the missing semi-auto locking sleeve on the M14 and M14DMR - and show me where it is on the RIS versions - I will look at correcting the problem on the M14s and M21s.
What should the M16A1 have in place the A2 flash hider?
As for the rest, as Serjames states, I am not the original modeller of the weapons - hence the credits in the release notes. They were either donated or made open source and available online with the correct accreditation. I am not in a position to make any major changes to the models, but I may be able to correct the small changes, and correct the config for the burst settings.
Thanks.
in the 1960's, the M14 was found to be borderline uncontrollable in full auto due to the more traditional shape of the stock - even adding a "flip-up" stock piece didn't help much, so nearly all M14 rifles were converted to semi-auto only via a locking sleeve that physically prevented the movement of the sear disconnector on the return stroke of the carrier. this looks like a little round "knob" below the trip lever.
normal M14 before conversion (and some export rifles and rare escapees of the conversion process): https://steamhost.cn/steamcommunity_com/sharedfiles/filedetails/?id=2540374252
notice the "paddle" selector below the trip lever and the lever being "forward" in order to interact with the disconnector (on bolt return, the trip lever is forced forward, which if the selector is rotated properly will allow the movement of the lever's hand inside the receiver to push up on the sear, letting the hammer fall forward and fire again - this happens repeatedly until the trigger is released or the ammunition is exhausted).
after conversion: https://steamhost.cn/steamcommunity_com/sharedfiles/filedetails/?id=2540374121
notice the round locking collar that is permanently fixed in the "semi" position with the trip lever to the rear, detached from interacting with the disconnector. sometimes this collar is a sleeve instead with a pin holding the pivot in place. depend on who did the conversion.
while neither is identical to the real thing, both are close enough that few will notice.
commercially manufactured M14's (popularly known as M1A rifles) will lack the trip lever and collar/sleeve entirely:
https://imgur.com/F5Wp95U
as for the M16A1 flash hider, experiences with thick brush led to the original "duck bill" and "three prong" flashiders being discontinued in the mid-1960's. with the changes from the M16 to the M16E1, the rifle had the shell deflector added, a modified butt-stock with storage compartment, chrome-lined bore and phosphated carrier with chrome-lining on the interior, a forward assist, a modified pistol grip, changes to small parts for mass manufacturing, but the flashider was "closed" at the end, being nicknamed the "birdcage".
it had six slots spaced equally around the device and was otherwise identical to the A2 birdcage used on the M16A2 and later come the 1980's.
https://imgur.com/K428Izy
this is why in movies like Predator, you see a star-burst pattern all around, rather than only the top. if you look carefully you can see the bottom of the flash hider has a slot cut there, allowing gasses to escape. btw that flash is great exaggerated for theatrical purposes using a restrictor and blanks.
https://imgur.com/fIGeECQ
the M16A2's flash hider has 5 slots, slightly closer together, with the "bottom" of the flash hider (the side facing the ground when the rifle is shouldered) where the sixth slot used to be no longer being cut. this meant slightly less dust being kicked up when prone and a very slight "compensating" effect because hot gasses from firing are directed upwards mostly.