安裝 Steam
登入
|
語言
簡體中文
日本語（日文）
한국어（韓文）
ไทย（泰文）
Български（保加利亞文）
Čeština（捷克文）
Dansk（丹麥文）
Deutsch（德文）
English（英文）
Español - España（西班牙文 - 西班牙）
Español - Latinoamérica（西班牙文 - 拉丁美洲）
Ελληνικά（希臘文）
Français（法文）
Italiano（義大利文）
Bahasa Indonesia（印尼語）
Magyar（匈牙利文）
Nederlands（荷蘭文）
Norsk（挪威文）
Polski（波蘭文）
Português（葡萄牙文 - 葡萄牙）
Português - Brasil（葡萄牙文 - 巴西）
Română（羅馬尼亞文）
Русский（俄文）
Suomi（芬蘭文）
Svenska（瑞典文）
Türkçe（土耳其文）
tiếng Việt（越南文）
Українська（烏克蘭文）
回報翻譯問題
3 
檢舉此篇文章
if so remember the payload blocks are actually sitting in the space off to the side of the torpedo as far as the game is concerned. thus to weld them you must either weld on the spot next to the torpedo or se a welder that welds with a big eneugh radius to hit blocks near it.
I gotta say, my little project is coming along nicely. I've created an auto loading system using timer blocks and the maglock mod.
Phase 1- Kicks on the welders and creates a torpedo (my Mk-79 ADCAP using your parts). Once the torp is welded (custom adjust the timer blocks based on creative or survival), then uses a hard point on a piston to merge the torp and lower it to tube loading position.
Phase 2- Loads the torp into the tube by executing these actions: Maglock engaged to hold the torp and the hard point disengages and moves out of the way. The inner tube door opens and the ram loads the torp into the chamber and holds it steady. While in firing position a set of doors in the bottom of the tube opens and a hard point on a piston rises to merge with the torp to hold it, the Maglock disengages and the ram retracts, inner tube door closes.
Phase 3 - Where the fun begins. You must select a fire mode for the torpedo, either "dumb" (missile mode:passive) or Active remote control.
Phase 4 a - passive mode : torp guidance is set to gyro override (to keep it tracking straight) and the warhead safeties are disengaged. Outer door of the tube is opened.
Phase 4 b - active mode : torp antenna is activated
FIRE Tube 1 - Upon pressing the fire button the following actions occurr: Hard point is disengaged and the piston starts moving out of the way. 2 seconds later the tubes grav gens and the mass block on the torp activate to accelerate the torp out of the tube (simulates using compressed air to push a torp out of a tube) meanwhile the Torp's main thruster turns on.
In passive mode it will fly straight (you can use the cam on the torp to aim it down the tube. This is not all that unlike a submarine in WWI or WWII.
In Active mode you would select the ship from your menu click control and then use the camera. Active mode is best for known targets at up to 50km away and as close as 10km if your a fast clicker.
Is this an over complicated mess, yup, but it's fun, and it works beautifully. I went to the extra trouble of the tube doors because of the keen blog post about atmospheres eventually. No need to vent all your oxygen to space just to fire the main weapon.
We also tested it vs a couple of custom built and workshop large ships, mostly in the 1.5 mil ton range. Most of these are torn in two if hit broadside. I sent one down the nose of my buddy's mining hauler and it obliterated the bridge, along with the bulk of the ship down to the drone bays.
I own my own dedicated server and plan to build and test this there as well :)
https://steamhost.cn/steamcommunity_com/sharedfiles/filedetails/?id=410208858