Store Page
Stormworks: Build and Rescue
All Discussions Screenshots Artwork Broadcasts Videos Workshop News Guides Reviews

Stormworks: Build and Rescue

Store Page
Stormworks: Build and Rescue >  Workshop > Edomite2277's Workshop > FSM 410104 Nuclear Steam Locomotive
FSM 410104 Nuclear Steam Locomotive
Description Discussions0 Comments14 Change Notes
14 Comments
< >
Edomite2277  [author] 15 Jul @ 10:41am 
As stated at the bottom of the description, it requires either the large build zone near the monkey brain launch site on the Arid Island from the industrial DLC, or an XML edited workbench.
nodrog03 14 Jul @ 12:38pm 
where do you spawn it?????????///
pilothyperdrive 13 Jul @ 6:46pm 
tbh i missed this nuclear beast of an engine, i used the original one as an armored train.
Edomite2277  [author] 15 Jun @ 10:33am 
its in the description: 8675
jodapf 15 Jun @ 9:23am 
WHATS THE CODE?
Edomite2277  [author] 9 Jun @ 8:28am 
It can melt down, yes. If you don't monitor the reactor, the control rods can get too hot. There is a warning buzzer that will activate if it gets too hot.
pepijnsiem 9 Jun @ 5:21am 
im not an expert in nucliar stuff but can this train go boom?
andrijromanuk006 8 Jun @ 8:16am 
░░░░░▄▄▄░░▄██▄░░░
░░░░░▐▀█▀▌░░░░▀█▄░░░
░░░░░▐█▄█▌░░░░░░▀█▄░░
░░░░░░▀▄▀░░░▄▄▄▄▄▀▀░░
░░░░▄▄▄██▀▀▀▀░░░░░░░
░░░█▀▄▄▄█░▀▀░░
░░░▌░▄▄▄▐▌▀▀▀░░ THIS IS BOB
▄░▐░░░▄▄░█░▀▀ ░░
▀█▌░░░▄░▀█▀░▀ ░░ COPY AND PASTE HIM,
░░░░░░░▄▄▐▌▄▄░░░ SO, HE CAN TAKE
░░░░░░░▀███▀█░▄░░ OVER THE WORKSHOP
░░░░░░▐▌▀▄▀▄▀▐▄░░
░░░░░░▐▀░░░░░░▐▌░░
Edomite2277  [author] 5 Jun @ 11:34am 
wait for them to reach zero. its one for each steam chest, front and rear. they should drain at the same rate, but check both just in case.
randomdude0429 5 Jun @ 11:10am 
when draining, do we have to wait for both dials to hit zero or do we have to wait for them to reach zero
Edomite2277  [author] 5 Jun @ 6:34am 
That sounds like you didn't drain the steam chest before running. Did you open the cylinder drains (steam wont let me use the real term, but they are the button closest to the floor) and reverser before you started running? For some reason, if there is any air in the steam chest, the cylinders will slowly clog.
randomdude0429 4 Jun @ 7:31pm 
im having trouble getting it working, after a bit of time running it slows down and stops
Fern 3 Jun @ 12:31pm 
Truly a gorgeous engine :3
Aurora System 3 Jun @ 12:29pm 
about damn time smh my head